Using ms and converting to us is a bad idea as we still get ms
granualrity in us units. Use the proper API to get us granularity.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Utilize a code spell-checking tool to scan for and correct spelling errors
in `Kconfig` files within the `arch`, `boards`, `kernel`, `modules`,
`samples`, and `share` directory.
Additionally, incorporates a fix recommended by the reviewer.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
In case anyone enabled EAP_*_ALL explicitly without enabling the
Enterprise then it leads to a build error.
Fix by adding the dependency.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
[Description]
After starting a DPP soft ap, enter 'wifi ap status'.
Security is shown as 'UNKNOW'.
[Root Cause]
1. Start a DPP soft ap:
wifi ap enable -s xxx -c x -p xxx -k 11
The parameter '-k 11' corresponds to
zephyr security type 'WIFI_SECURITY_TYPE_DPP'.
2. hapd_config_network() will be called to config a
new hostap bss.
3. Filed 'bss->wpa_key_mgmt' is set to
WPA_KEY_MGMT_PSK | WPA_KEY_MGMT_DPP.
4. When try to get security type of DPP soft ap,
there is no corresponding zephyr security type.
[Fix]
Add enhance code to convert the security type
to zephyr DPP security type.
Signed-off-by: Qiankun Li <qiankun.li@nxp.com>
When QSPI LPM is enabled, QSPI will already be uninitialized, and during
deinit if uninitialized is being called again then it leads to a hang as
it waits for mem busy check to pass which it won't.
Fix by checking if the device is initialized before calling
uninitialize.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
Add support for the frame buffer address and stride alignment.
If user set the CONFIG_LV_DRAW_BUF_ALIGN to not be 4, the buffers
shall be allocated aoocrdingly.
If user set the CONFIG_LV_DRAW_BUF_STRIDE_ALIGN to not be 1, the
methods of flushing the display shall set the pitch accordingly.
Signed-off-by: Kate Wang <yumeng.wang@nxp.com>
Enalbe II2C hal driver status polling timeout in order to avoid
blocking of some driver API, such as kernel hang during i2c scanning.
Signed-off-by: Jiafei Pan <Jiafei.Pan@nxp.com>
Earlier we had socketpair to pass wifi event information from
wpa_supplicant side to zephyr adaption layer. This is now replaced
by k_fifo to save some RAM.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
1. When external station connects to soft ap, zephyr
hostap will fill sta_info before sending mgmt event
to l2 wifi layer.
sta_info.twt_capable should be filled with external
station capability rather than soft ap self.
2. Rename hapd_is_twt_capable to
hapd_get_sta_he_twt_capable.
Try to get twt_capa form capability of external station
rather than soft ap.
Signed-off-by: Qiankun Li <qiankun.li@nxp.com>
The clock startup latency is now obtained from the clock driver and the
nrf-802154 is now set to a value that matches hardware capabilities.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
The nrf-802154 component of hal_nordic is updated.
The CCA threshold configuration is now done in dBm units, instead of
hardware-dependent scale.
Fixed a bug, where the CONFIG_NRF_802154_CCA_ED_THRESHOLD units were
different from the NRF_802154_CCA_ED_THRESHOLD units. Now all
configuration is done in dBm.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
I2S driver support standard format, short/long sync, left/right justified.
Supporting 2 channels as a default.
Signed-off-by: Lewis Lee <llee@ambiq.com>
Add a snippet for Wi-Fi credentials support. Update the heap sizes as
required for enterprise mode.
Signed-off-by: Ravi Dondaputi <ravi.dondaputi@nordicsemi.no>
Add PWM driver for the Timer peripheral on Series 2.
The TIMER uses the high-frequency EM01 Group A clock, and has
a 16- or 32-bit counter. It supports PWM period and pulse capture
on channel 0, and PWM output on all channels.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Add PWM driver for the Low Energy Timer peripheral on Series 2.
The LETIMER runs at up to 32 kHz and has a 24-bit counter. It
only supports PWM output, it does not support input capture.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
- Update to use ETHOS_U config instead of ARM_ETHOS_U
- Update prefix ETHOS_U_ for all configs that use ARM_ETHOS_U_
Signed-off-by: Khoa Nguyen <khoa.nguyen.xh@renesas.com>
1. The edma version 5 share one driver with edma 4.
2. Edma5 tcd structure some difference, Use tcd type to distinguish,
and Edma5 uses 64 bytes for alignment instead of 32.
3. Some platforms have some address offsets for certain memory
when processing from a DMA perspective, such as imx95 cm7 TCM,
so add offset processing.
Signed-off-by: Yongxu Wang <yongxu.wang@nxp.com>
What is changed?
Added config for Ethos-U65 for Corstone315 which has default 256 MACs
as per FVP.
Why do we need this change?
This will help in validating the NPU when we add support for FVP
testing for Ethos-U65.
Signed-off-by: Shaunak saha <ssaha@tsavoritesi.com>
Add initial support for i2c on Renesas RX MCU
This driver is controlling the RIIC HW of RX MCU for i2c bus
interface on Zephyr
Only master mode is supported
Signed-off-by: Duy Nguyen <duy.nguyen.xa@renesas.com>
Current code would have systematically tried to add the FS_O_CREATE flag
when opening a file in read mode. This effectively made it impossible to
open files to read them on read-only file systems.
Signed-off-by: Benjamin Cabé <benjamin@zephyrproject.org>
Release the SPI during the deinit to put respective GPIOs in low-power
state or disconnected.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
By default QSPI is uninitialized after every transaction, so, deinit is
a no-op, but if QSPI_LOW_POWER is disabled, then we need to uninitialize
the QSPI in the deinit.
Signed-off-by: Chaitanya Tata <Chaitanya.Tata@nordicsemi.no>
For optimization purpose, remove calls to SDK. Since we know exactly
what we want, this results in smaller code size.
Also, this code calculates the SCK parameters more efficiently than the
SDK driver did it by using a binary (instead of linear) search.
Lastly, remove call to LPSPI_Reset in the init call and replace with
native driver code, and remove inclusion of SDK header.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Implies the Kconfig symbol for generated a padded, confirmed image
when MCUboot has been configured in directxip mode with revert, as
the main image must be confirmed in order for it to be booted
Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>
Refactor the controller init to use the new init routines the
controller now provides. Instead of using a hardcoded set of
features, the features are now initialized based on Kconfig
values that the application selects.
Add config files under modules/hal_silabs, used by the controller
init routines in the external module hal_silabs to determine which
features to enable based on Kconfig options. This brings the
controller feature configurability to roughly parity with the
Simplicity SDK.
Signed-off-by: Jori Rintahaka <jori.rintahaka@silabs.com>
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Update the Simplicity SDK HAL for Silicon Labs Series 2
devices to v2025.6.0.
The em_core source file no longer exists in the latest version
of the HAL, and is removed.
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Added kconfig for regulatory domain in hostapd. Default is set to
00 as World Wide mode.
Also added 3rd octet kconfig to set regulatory environment and set
it to 32 for all supported environments.
Signed-off-by: Abhinav Kulkarni <abhinav.kulkarni@nxp.com>
Instead of using 32 bit enum values for event numbers, convert
the code to use 64 bit long bit fields. This means that the
user API is changed to use 64 bit event values instead of 32
bit event values.
Signed-off-by: Jukka Rissanen <jukka.rissanen@nordicsemi.no>
This commit makes the Radio workqueue priority configurable by the
application. Additionally, the default priority has been adjusted to
allow transmit operations to occur before the entire RX queue is
processed.
Signed-off-by: Łukasz Duda <lukasz.duda@nordicsemi.no>
Cleaned up NETC driver in drivers.cmake to add i.MX943 NETC
driver support, and to disable msgintr/irqsteer for A core.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Łukasz Duda
Jamie McCrae
Nazar Palamar
Chaitanya Tata
Pisit Sawangvonganan
Piotr Koziar
Qiankun Li
Karol Lasończyk
Kate Wang
Jiafei Pan
David Jewsbury
Jukka Rissanen
Ta Minh Nhat
Rafał Kuźnia
Sebastian Głąb
Lewis Lee
Khoa Tran
Ravi Dondaputi
Aksel Skauge Mellbye
Khoa Nguyen
Yongxu Wang
Shaunak saha
Duy Nguyen
Tamas Jozsi
Jérôme Pouiller
Benjamin Cabé
Declan Snyder
Jori Rintahaka
Jakub Zymelka
Abhinav Kulkarni
Yangbo Lu