boards: arm: xiao_ble: Convert to v2

Converts the board to hwmv2

Signed-off-by: Jamie McCrae <jamie.mccrae@nordicsemi.no>

boards/boards_legacy/arm/xiao_ble/xiao_ble_sense_defconfig

@@ -1,33 +0,0 @@
-# SPDX-License-Identifier: Apache-2.0
-
-CONFIG_SOC_SERIES_NRF52X=y
-CONFIG_SOC_NRF52840_QIAA=y
-CONFIG_BOARD_XIAO_BLE=y
-
-# Enable MPU
-CONFIG_ARM_MPU=y
-
-# Enable hardware stack protection
-CONFIG_HW_STACK_PROTECTION=y
-
-# enable GPIO
-CONFIG_GPIO=y
-
-# enable uart driver
-CONFIG_SERIAL=y
-
-# enable console
-CONFIG_CONSOLE=y
-
-# Logger cannot use itself to log
-CONFIG_USB_CDC_ACM_LOG_LEVEL_OFF=y
-
-# enable USB
-CONFIG_USB_DEVICE_STACK=y
-
-# Build UF2 by default, supported by the Adafruit nRF52 Bootloader
-CONFIG_BUILD_OUTPUT_UF2=y
-CONFIG_USE_DT_CODE_PARTITION=y
-
-# required to enable LSM6DS3TR-C power
-CONFIG_REGULATOR=y

boards/qemu/qemu_cortex_m0/board.yml

@@ -1,3 +1,5 @@
 board:
   name: qemu_cortex_m0
   vendor: Nordic Semiconductor
+  socs:
+  - name: nrf51822

boards/seeed_studio/xiao_ble/Kconfig.defconfig

@@ -5,14 +5,9 @@
 
 if BOARD_XIAO_BLE
 
-config BOARD
-	default "xiao_ble"
-
 config BT_CTLR
 	default BT
 
-endif # BOARD_XIAO_BLE
-
 if USB_DEVICE_STACK
 
 config UART_CONSOLE
@@ -22,3 +17,5 @@ config USB_DEVICE_INITIALIZE_AT_BOOT
 	default y
 
 endif # USB_DEVICE_STACK
+
+endif # BOARD_XIAO_BLE

boards/seeed_studio/xiao_ble/Kconfig.xiao_ble

@@ -4,5 +4,4 @@
 # SPDX-License-Identifier: Apache-2.0
 
 config BOARD_XIAO_BLE
-	bool "XIAO BLE"
+	select SOC_NRF52840_QIAA
-	depends on SOC_NRF52840_QIAA

boards/seeed_studio/xiao_ble/board.yml

@@ -0,0 +1,5 @@
+board:
+  name: xiao_ble
+  vendor: Seeed Studio
+  variants:
+  - name: 'sense'

boards/seeed_studio/xiao_ble/doc/index.rst

@@ -146,7 +146,7 @@ initialized before any text is printed, as below:
 
       .. zephyr-app-commands::
          :zephyr-app: samples/hello_world
-         :board: xiao_ble_sense
+         :board: xiao_ble/nrf52840/sense
          :goals: build flash
          :gen-args: -DCONFIG_BOOT_DELAY=5000
 
@@ -177,12 +177,12 @@ properly with Zephyr:
 
       .. zephyr-app-commands::
          :zephyr-app: samples/basic/blinky
-         :board: xiao_ble_sense
+         :board: xiao_ble/nrf52840/sense
          :goals: build flash
 
 You can build and flash the examples to make sure Zephyr is running correctly on
 your board. The LED definitions can be found in
-:zephyr_file:`boards/arm/xiao_ble/xiao_ble_common.dtsi`.
+:zephyr_file:`boards/xiao_ble/xiao_ble_common.dtsi`.
 
 Testing shell over USB in the XIAO BLE (Sense)
 **********************************************
@@ -203,7 +203,7 @@ with Zephyr:
 
       .. zephyr-app-commands::
          :zephyr-app: samples/subsys/shell/shell_module
-         :board: xiao_ble_sense
+         :board: xiao_ble/nrf52840/sense
          :goals: build flash
 
 References

boards/seeed_studio/xiao_ble/xiao_ble_defconfig

@@ -1,28 +1,24 @@
 # SPDX-License-Identifier: Apache-2.0
 
-CONFIG_SOC_SERIES_NRF52X=y
-CONFIG_SOC_NRF52840_QIAA=y
-CONFIG_BOARD_XIAO_BLE=y
-
 # Enable MPU
 CONFIG_ARM_MPU=y
 
 # Enable hardware stack protection
 CONFIG_HW_STACK_PROTECTION=y
 
-# enable GPIO
+# Enable GPIO
 CONFIG_GPIO=y
 
-# enable uart driver
+# Enable UART driver
 CONFIG_SERIAL=y
 
-# enable console
+# Enable console
 CONFIG_CONSOLE=y
 
 # Logger cannot use itself to log
 CONFIG_USB_CDC_ACM_LOG_LEVEL_OFF=y
 
-# enable USB
+# Enable USB
 CONFIG_USB_DEVICE_STACK=y
 
 # Build UF2 by default, supported by the Adafruit nRF52 Bootloader

boards/seeed_studio/xiao_ble/xiao_ble_nrf52840_sense.yaml

@@ -1,4 +1,4 @@
-identifier: xiao_ble_sense
+identifier: xiao_ble/nrf52840/sense
 name: XIAO BLE Sense
 type: mcu
 arch: arm

boards/seeed_studio/xiao_ble/xiao_ble_nrf52840_sense_defconfig

@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: Apache-2.0
+
+# Required to enable LSM6DS3TR-C power
+CONFIG_REGULATOR=y