Fixing multiple things related to psram usage:
- fix conflicting psram0 dts node for all ESP32 SiP and SoC.
- fix dcache and icache area used in psram mapping.
- fix smh spiram heap allocations.
- add `espressif,esp32-psram` compatible to set psram0 size in dts.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
This WDT is responsible for monitoring the external
32.728 Hz crystal connected to pins XTAL_32K_P and
XTAL_32K_N. If an oscillation failure is detected
the hardware automatically switch to RTC_RC_SLOW
clock source and triggers an interrupt.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
The RTC subsystem in espressif's SOCs, among other tasks
is responsible for clock selection for CPU and for low
power domain clocks such as RTC_SLOW and RTC_FAST.
This commit allows for proper clock source and rate
selection for CPU, using the espressif,riscv and
espressif,xtensa-lx6/7 bindings.
It also enables clock selection for RTC_FAST and RTC_SLOW,
that impacts some peripherals, such as rtc_timer.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Introduce dtsi files representing the
current portfolio of chips and modules
based on the followint criteria:
- flash size
- psram size
- gpio count
- certification status
Update the boards dts files according
to which SOC/SIP they are using.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
CPU idle states are not board specific. This patch moves ESP32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
- Add overlay for the esp32s2_saola board to die_temp_polling sample.
- Add aliases for the die_temp_polling sample to esp32s2 dtsi.
Signed-off-by: Hiroki Tada <tada.hiroki@fujitsu.com>
Support for the measuring the CPU die temperature
for the ESP32 targets S2,C3. The ESP32 support
was ommited due to lack of offset calibration.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
On Espressif SoCs, the pin controller is a virtual device.
Pin settings are actually controlled in a distributed way.
Therefore, that node does not belong to the SoC bus.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
Not all boards use the same UART's defaults properties.
This commit updates device tree declarations by deferring
specific definitions to the board's DTS.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Use i2c_hal functions to enable support for
multiple SoCs.
Use DT compat to enable I2C from device
tree configuration
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
This joins all clock control handling to same source
by using hal clock functions. It also brings ESP32C3
clock support.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
1) Allow use of interrup driven instance.
ROM implementation could be selected via dts compatiable.
2) Use UART rx fifo and timeout interrupt for end of message detection.
Added to decrease interrupts count on data reception
3) Use ESP_LL api.
Signed-off-by: Pavlo Hamov <p.hamov@venstar.com>
Joel Guittet
Marcio Ribeiro
Marek Matej
Raffael Rostagno
Sylvio Alves
Johan Hedberg
Lucas Tamborrino
Henrik Brix Andersen
Gerard Marull-Paretas
Gerard Marull-Paretas
Hiroki Tada
Benjamin Björnsson
Moritz Fischer
Glauber Maroto Ferreira
Kumar Gala
Pavlo Hamov