Fixing multiple things related to psram usage:
- fix conflicting psram0 dts node for all ESP32 SiP and SoC.
- fix dcache and icache area used in psram mapping.
- fix smh spiram heap allocations.
- add `espressif,esp32-psram` compatible to set psram0 size in dts.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
Set AMP dts nodes (ipm, mbox, ...) to use fixed locations in reserved
memory areas. Those areas memories are delimited in the `memory.h`.
Size of the occupied areas can be calculated but the dts nodes addresses
needs to be set manually in every case.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
The RTC subsystem in espressif's SOCs, among other tasks
is responsible for clock selection for CPU and for low
power domain clocks such as RTC_SLOW and RTC_FAST.
This commit allows for proper clock source and rate
selection for CPU, using the espressif,riscv and
espressif,xtensa-lx6/7 bindings.
It also enables clock selection for RTC_FAST and RTC_SLOW,
that impacts some peripherals, such as rtc_timer.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Remove all optional, initial CAN sample point properties and rely on the
CAN timing calculations to automatically pick the preferred sample point
location based on the initial bitrate.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Updates Ethernet PHY devicetree bindings to be more consistent with
Linux by using the standard `reg` property for the PHY address instead
of a custom `address` property. As a result, MDIO controller bindings
now require standard `#address-cells` and `#size-cells` properties.
Signed-off-by: Maureen Helm <maureen.helm@analog.com>
Update the descriptions for the various CAN devicetree timing properties
specified in Time Quanta (TQ) to make it clear that these, if present, are
only used for the initial timing parameters.
Deprecate the (Re-)Synchronization Jump Width (SJW) devicetree properties
for both arbitration and data phase timing as these are now only used in
combination with the other TQ-based CAN timing properties, which are all
deprecated.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add `mdio_read_c45()`/`mdio_write_c45()` APIs for Clause 45 access
and remove the `protocol` MDIO binding property so that MDIO bus
controller can support more than one protocol.
A new MDIO header is introduced with generic opcodes, MMD and
registers addresses, to be used by MDIO and PHY drivers.
Existing MDIO drivers that support both Clause 22 and Clause 45
access are migrated to the new APIs.
Signed-off-by: Manuel Argüelles <manuel.arguelles@nxp.com>
Introduce dtsi files representing the
current portfolio of chips and modules
based on the followint criteria:
- flash size
- psram size
- gpio count
- certification status
Update the boards dts files according
to which SOC/SIP they are using.
Signed-off-by: Marek Matej <marek.matej@espressif.com>
CPU idle states are not board specific. This patch moves ESP32 idle
states to the core SoC dts files. Board can always tweak some state
parameters (if needed), but the definition belongs to core SoC dts
files, same as e.g. peripherals.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
This reverts commit fdd47f39be.
After v4.4.1, write-block-size is no longer needed to be 32-bytes
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
- adds properties 'group', 'index' and 'prescaler'.
- updates board's dts to include those properties.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
This commit moves the hardware configuration for ledc
peripheral to the device-tree instead of Kconfig.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
Current write block size does not guarantee proper
write operation, what might cause corrupted data.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
On Espressif SoCs, the pin controller is a virtual device.
Pin settings are actually controlled in a distributed way.
Therefore, that node does not belong to the SoC bus.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
In order to bring consistency in-tree, migrate all dts code to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to zephyrproject-rtos#45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Add a GPIO pass-thru map for accessing the full range (0 to 39) of ESP32
GPIO pins by their datasheet number.
GPIOs 0 to 31 are mapped to gpio0 while GPIOs 32 to 39 are mapped to
gpio1.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
The pinctrl support made usage of the 'peripheral'
property no longer required.
Signed-off-by: Glauber Maroto Ferreira <glauber.ferreira@espressif.com>
Current uart driver implementation is incompleted regarding the
usage of DT_INST_FOREACH_STATUS_OKAY. If uart0 and uart2 are selected,
build breaks due to peripheral number ordering, which would be
0 and 1 in this case. This fix PR fix this by re-working the macros
and setting proper uart peripheral instances in DTSI, required for signal
routing configuration.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
By enabling SMP option plus the APPCPU, also
completes the SMP port by adding the esp32
specific arch_sched_ipi() function
Signed-off-by: Felipe Neves <felipe.neves@espressif.com>
Joel Guittet
Marcio Ribeiro
Marek Matej
Raffael Rostagno
Sylvio Alves
Felipe Neves
Johan Hedberg
Lucas Tamborrino
Henrik Brix Andersen
Maureen Helm
Manuel Argüelles
Gerard Marull-Paretas
Gerard Marull-Paretas
Benjamin Björnsson
Felipe Neves
Grant Ramsay
Henrik Brix Andersen
Glauber Maroto Ferreira
Kumar Gala
Felipe Neves