The Drivers using Pinctrl should be turning Pinctrl on
this should not be the responsibility of the board. This
commit removes CONFIG_PINCTRL from the boards side for nxp boards.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Update serial drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references
where needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Refactors the mcux lpsci shim driver to use the clock control interface
instead of calling CLOCK_GetFreq() directly. This will allow SoCs with
different clock architectures to reuse this driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
SoCs outside the Kinetis family can have the LPSCI module, so move the
HAS_LPSCI config from arch/arm/soc/nxp_kinetis to ext/hal/nxp/mcux
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
As not all drivers support interrupts we don't have a means to know if
we can allow UART_INTERRUPT_DRIVEN to be enabled and thus various
Kconfig options that select UART_INTERRUPT_DRIVEN. Some drivers have a
interrupts, however not all do. So introduce a Kconfig option to let us
know what the driver actually supports.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we can utilize label in the device tree we can convert to
getting the device name for the NXP Kinetis UART out of the device tree
instead of from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adds a shim layer around the mcux lpsci driver to adapt it to the Zephyr
serial interface.
Change-Id: I024f1605e3194f34bb57e8a121900e05b3085a82
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Emilio Benavente
Kumar Gala
Kumar Gala
Ulf Magnusson
Maureen Helm