Disable the pwmleds nodes in the dts overlay for rev B/C boards. The
FLEXPWM is not routed to LED on these versions.
Fixes#92285
Signed-off-by: David Leach <david.leach@nxp.com>
This commit updates the link to the source of the firmware of the DAPLink
on-board debug adapter.
Phytec migrates all repositories from the "PHYTEC-Messtechnik-GmbH" GitHub
organization to the "phytec" GitHub organization. The code in the relevant
branch remains unchanged and the branch has been pushed to the new
organization.
Signed-off-by: Jonas Remmert <j.remmert@phytec.de>
All Nordic boards were enabling CONFIG_HW_STACK_PROTECTION
unconditionally, which is usually not a problem except if the particular
application happens to want to disable the MPU (or equivalent hardware
for RISC-V). In that case, the following warning is shown:
warning: HW_STACK_PROTECTION (defined at arch/Kconfig) was assigned the
value 'y' but got the value 'n'.
Check these unsatisfied dependencies: ARCH_HAS_STACK_PROTECTION (=n).
In order to avoid this warning, conditionally enable the hardware stack
protection only when the architecture supports it.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Remove cmake code that updated the linkserver memory view, however
the values passed here are wrong and linkserver already includes
the correct space e.g location = 0x0 && size = 0x00080000
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
Updated board.cmake to check for single
image builds to indicate rather an additional
reset is needed for cases such as sysbuild.
Signed-off-by: Emilio Benavente <emilio.benavente@nxp.com>
define stm32_lp_tick_source since PM is looking for this node
and change clock source for lptim2 to lsi.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
This adds the generic plugable alias to the Adafruit RP2040 QT PY for
its STEMMA-QT connector.
Signed-off-by: Ian Wakely <raveious.irw@gmail.com>
Signed-off-by: Ian Wakely <raveious.irw@gmail.com>
Instead of having a conf file for all variants of STM32N6570_DK,
set the necessary settings for any platform which has DCMIPP enabled.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Clarify expectations about the recently modified default variant of the
board.
Update migration guide to warn existing users about the change.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
as in mbox cases the ocram is used as code area, so shall not be used
as sram again. this is a typo introduced by
aec0355380
fixing: #82841
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Utilize a code spell-checking tool to scan for and correct spelling errors
in `Kconfig` files within the `arch`, `boards`, `kernel`, `modules`,
`samples`, and `share` directory.
Additionally, incorporates a fix recommended by the reviewer.
Signed-off-by: Pisit Sawangvonganan <pisit@ndrsolution.com>
The DT hierachy of the RT11xx series was somewhat incoherent. The boards
targets were directly including the series level DTSI with no SOC dtsi
in between, and there existed an SOC DTSI that had to be separately
included by a different board file, which didn't include the series DTSI
itself. It seems that this was only working if you included the files
exactly in the correct order in specific board files. Also, as a result
of this change, need to (correctly) define the cpu core only in the DTSI
for that core, instead of in the series generic dtsi, because that DTSI
was actually written with incorrect syntax due to duplicated node labels
on nodes right next to each other in the same file, and was relying on
other DTSI files to delete the duplicate nodes in order for it to build.
So overall this was a mess, needed cleanup.
Signed-off-by: Declan Snyder <declan.snyder@nxp.com>
Add support for Waveshare RP2040 Plus board a Raspberry Pi Pico like
board including a battery charger.
Signed-off-by: David Schneider <schneidav81@gmail.com>
1. add the ostimer
2. by default, the systick is used.
3. The ostimer could be tested with below configure in xxx.overlay:
&systick {
status = "disabled";
};
&ostimer0 {
status = "okay";
};
And below configure in xxx.conf:
CONFIG_SYS_CLOCK_HW_CYCLES_PER_SEC=1000000
Signed-off-by: Peter Wang <chaoyi.wang@nxp.com>
Make the stm32n6_dk variant (stm32n6570_dk/stm32n657xx/fsbl) unable
to execute tests in CI with Twister.
This change will help avoid many CI build failures caused by this variant.
Signed-off-by: Fabrice DJIATSA <fabrice.djiatsa-ext@st.com>
Use runners_yaml_props_target to set the name of the file to
flash, rather than hard-coding it for each board.
Co-developed-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Signed-off-by: Aksel Skauge Mellbye <aksel.mellbye@silabs.com>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
1. Increased interfaces count as there are 6 MACs on i.MX943.
2. Increased NETC ring length as extended BD will be used.
3. Enabled monitor for gPTP sync status.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
- fixes is25wp064 flash size in DTS. It must be 8 MBytes (64MBits).
- uses DT_SIZE_M() macro instead of an absolute value.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
This set of changes adds support for QSPI-based external flash and
Bluetooth to the device tree. This make it possible to correctly build and
execute the fatfs and several Bluetooth samples out of the box.
Also added a function to read the external flash OTP to extract
information about the Opta model and hardware features and a second
function to retrieve the "official" Opta serial number.
Signed-off-by: Federico Di Gregorio <fog@dndg.it>
Addition of a shield st_mb1897_cam embedding a GC2145 CSI
sensor which can be connected to the STM32MP135F-DK via a 15pins FFC.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
The STM32MP135F-DK board embeds a ST-MIPID02 CSI to DVP
bridge allowing to connect a CSI 15pins FFC cable enabled
sensor to the DCMIPP in parallel interface.
Add the ST-MIPID02 node and its dependency MCO clock as well
as partially filled DCMIPP node.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
MCP230XX IO expander is interfaced via i2c hence it is
suffisant to align its init priority to the i2c one.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
The Arduino Nicla Vision board supports the new device_next USB stack
and can be used for testing USB Device features such as UVC.
Signed-off-by: Josuah Demangeon <me@josuah.net>
Fixes/adds jedec-id for is25wp128, is25lp064 and w25q512jvfiq flashes,
according to information from Flash data-sheets.
Signed-off-by: Andrej Butok <andrey.butok@nxp.com>
David Leach
Jonas Remmert
Carles Cufi
Emilio Benavente
Fabrice DJIATSA
Ian Wakely
Alain Volmat
Abhinav Kulkarni
Erwan Gouriou
Hake Huang
Jan Behrens
Grzegorz Swiderski
Khaoula Bidani
Pisit Sawangvonganan
Cong Nguyen Huu
Matthew Wood
Fin Maaß
Declan Snyder
Sylvio Alves
Karol Lasończyk
David Schneider
Stanley Huang
Andrew Perepech
Peter Wang
Kate Wang
Tamas Jozsi
Jérôme Pouiller
Mert Ekren
Yangbo Lu
Andrej Butok
Federico Di Gregorio
Josuah Demangeon
Steven Chang
Saravanan Sekar
Duy Nguyen
Ta Minh Nhat
Andrew Davis
Henrik Brix Andersen