You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
131 lines
3.6 KiB
131 lines
3.6 KiB
.. _sparkfun_pro_micro_rp2040: |
|
|
|
SparkFun Pro Micro RP2040 |
|
######################### |
|
|
|
Overview |
|
******** |
|
|
|
The SparkFun Pro Micro RP2040 is a small, low-cost, versatile board from |
|
SparkFun. It is equipped with an RP2040 SoC, an on-board WS2812 addressable |
|
LED, a USB connector, and a Qwiic connector. The USB bootloader allows it |
|
to be flashed without any adapter, in a drag-and-drop manner. |
|
|
|
Hardware |
|
******** |
|
- Dual core Arm Cortex-M0+ processor running up to 133MHz |
|
- 264KB on-chip SRAM |
|
- 16MB on-board QSPI flash with XIP capabilities |
|
- 18 GPIO pins |
|
- 4 Analog inputs |
|
- 1 UART peripherals |
|
- 1 SPI controllers |
|
- 2 I2C controllers (one via Qwiic connector) |
|
- 16 PWM channels |
|
- USB 1.1 controller (host/device) |
|
- 8 Programmable I/O (PIO) for custom peripherals |
|
- On-board RGB LED |
|
- 1 Watchdog timer peripheral |
|
|
|
|
|
.. figure:: img/sparkfun_pro_micro_rp2040.jpg |
|
:align: center |
|
:alt: SparkFun Pro Micro RP2040 |
|
|
|
SparkFun Pro Micro RP2040 (Image courtesy of SparkFun) |
|
|
|
Supported Features |
|
================== |
|
|
|
The sparkfun_pro_micro_rp2040 board configuration supports the following |
|
hardware features: |
|
|
|
.. list-table:: |
|
:header-rows: 1 |
|
|
|
* - Peripheral |
|
- Kconfig option |
|
- Devicetree compatible |
|
* - NVIC |
|
- N/A |
|
- :dtcompatible:`arm,v6m-nvic` |
|
* - UART |
|
- :kconfig:option:`CONFIG_SERIAL` |
|
- :dtcompatible:`raspberrypi,pico-uart` |
|
* - GPIO |
|
- :kconfig:option:`CONFIG_GPIO` |
|
- :dtcompatible:`raspberrypi,pico-gpio` |
|
* - ADC |
|
- :kconfig:option:`CONFIG_ADC` |
|
- :dtcompatible:`raspberrypi,pico-adc` |
|
* - I2C |
|
- :kconfig:option:`CONFIG_I2C` |
|
- :dtcompatible:`snps,designware-i2c` |
|
* - SPI |
|
- :kconfig:option:`CONFIG_SPI` |
|
- :dtcompatible:`raspberrypi,pico-spi` |
|
* - USB Device |
|
- :kconfig:option:`CONFIG_USB_DEVICE_STACK` |
|
- :dtcompatible:`raspberrypi,pico-usbd` |
|
* - HWINFO |
|
- :kconfig:option:`CONFIG_HWINFO` |
|
- N/A |
|
* - Watchdog Timer (WDT) |
|
- :kconfig:option:`CONFIG_WATCHDOG` |
|
- :dtcompatible:`raspberrypi,pico-watchdog` |
|
* - PWM |
|
- :kconfig:option:`CONFIG_PWM` |
|
- :dtcompatible:`raspberrypi,pico-pwm` |
|
* - Flash |
|
- :kconfig:option:`CONFIG_FLASH` |
|
- :dtcompatible:`raspberrypi,pico-flash` |
|
* - Clock controller |
|
- :kconfig:option:`CONFIG_CLOCK_CONTROL` |
|
- :dtcompatible:`raspberrypi,pico-clock-controller` |
|
* - UART (PIO) |
|
- :kconfig:option:`CONFIG_SERIAL` |
|
- :dtcompatible:`raspberrypi,pico-uart-pio` |
|
|
|
Pin Mapping |
|
=========== |
|
|
|
The peripherals of the RP2040 SoC can be routed to various pins on the board. |
|
The configuration of these routes can be modified through DTS. Please refer to |
|
the datasheet to see the possible routings for each peripheral. |
|
|
|
Default Zephyr Peripheral Mapping: |
|
---------------------------------- |
|
|
|
.. rst-class:: rst-columns |
|
|
|
- UART0_TX : P0 |
|
- UART0_RX : P1 |
|
- I2C1_SDA : P2 |
|
- I2C1_SCL : P3 |
|
- SPI0_RX : P20 |
|
- SPI0_SCK : P18 |
|
- SPI0_TX : P19 |
|
|
|
Programming and Debugging |
|
************************* |
|
|
|
Flashing |
|
======== |
|
|
|
Using UF2 |
|
--------- |
|
|
|
Since it doesn't expose the SWD pins, you must flash the SparkFun Pro Micro |
|
RP2040 with a UF2 file. By default, building an app for this board will |
|
generate a `build/zephyr/zephyr.uf2` file. If the Pro Micro RP2040 is powered |
|
on with the `BOOTSEL` button pressed, it will appear on the host as a mass |
|
storage device. The UF2 file should be drag-and-dropped to the device, which |
|
will flash the Pro Micro RP2040. |
|
|
|
.. target-notes:: |
|
|
|
.. _Getting Started with Raspberry Pi Pico: |
|
https://datasheets.raspberrypi.com/pico/getting-started-with-pico.pdf |
|
|
|
.. _Graphical Datasheet: |
|
https://cdn.sparkfun.com/assets/e/2/7/6/b/ProMicroRP2040_Graphical_Datasheet.pdf
|
|
|