Change automated searching for files using "IRQ_CONNECT()" API not
including <zephyr/irq.h>.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Many device pointers are initialized at compile and never changed. This
means that the device pointer can be constified (immutable).
Automated using:
```
perl -i -pe 's/const struct device \*(?!const)(.*)= DEVICE/const struct
device *const $1= DEVICE/g' **/*.c
```
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
Move gpio_cmsdk_ahb.h out of drivers/gpio and into include/drivers/gpio.
This is used by few board files so it should be in include.
This allows to remove few odd
"zephyr_library_include_directories(${ZEPHYR_BASE}/drivers)".
Signed-off-by: Fabio Baltieri <fabiobaltieri@google.com>
Add simple clock control node in devicetree for beetle to handle
relationship between drivers (uart, timers, gpio) and clock controller
device.
Signed-off-by: Kumar Gala <galak@kernel.org>
In order to bring consistency in-tree, migrate all drivers to the new
prefix <zephyr/...>. Note that the conversion has been scripted, refer
to #45388 for more details.
Signed-off-by: Gerard Marull-Paretas <gerard.marull@nordicsemi.no>
PRE_KERNEL_1 is to be used for devices that have no dependencies
and do not use kernel features, such as those that rely solely on
hardware present in the processor/SOC. This commit updates these
gpios to initialize during the PRE_KERNEL_1 rather than the
POST_KERNEL. Some SoC drivers are moved to PRE_KERNEL_2 due
to dependencies.
A lot of 'other' drivers can depend on GPIOs though phandles
(such as reset lines, data or command gpios, etc...). Most of these
drivers that would need this would come up on the POST_KERNEL,
and it's likely the driver may not be up yet as it should be defined.
Signed-off-by: Ryan McClelland <ryanmcclelland@fb.com>
Refactors all of the on-chip GPIO drivers to use a shared driver class
initialization priority configuration, CONFIG_GPIO_INIT_PRIORITY, to
allow configuring GPIO drivers separately from other devices. This is
similar to other driver classes like I2C and SPI.
Most drivers previously used CONFIG_KERNEL_INIT_PRIORITY_DEFAULT or
CONFIG_KERNEL_INIT_PRIORITY_DEVICE, therefore the default for this new
option is the lower of the two, which means earlier initialization.
Driver-specific options for off-chip I2C- or SPI-based GPIO drivers are
left intact because they often need to be initialized at a different
priority than on-chip GPIO drivers.
Signed-off-by: Maureen Helm <maureen.helm@intel.com>
Convert gpio drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
DEVICE_GET -> DEVICE_DT_GET
DEVICE_DECLARE -> DEVICE_DT_INST_DECLARE
etc..
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These are all the case that coccinelle cannot find as they are inside
macro declarations.
Fixed via:
git grep -rlz -E "\(struct device \*" |
xargs -0 sed -i 's/(struct device/(const struct device/g'
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This commit removes API functions and macros which were deprecated in
2.2 release. GPIO drivers are updated accordingly.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fixup cases of GPIO_PORT_PIN_MASK_FROM_NGPIOS(DT_INST_PROP(n, ngpios))
to use GPIO_PORT_PIN_MASK_FROM_DT_INST(n) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to utilize the new DT_INST macros completely and remove
associated Kconfig symbols that now come from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in arm_cmsdk/arm drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use gpio_pin_t uniformly when passing pin indexes to the driver. Use
gpio_flags_t uniformly when passing flags to the driver. Change name
of pin configuration function in API function table to be consistent
with other API functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The only remaining port operations have dedicated API function table
entries. Remove the defines for access op (mode), and remove support
for access op from all implementations.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The last external reference to these was removed when the pin
write/read functions were deprecated. Remove the syscall support, API
function table entries, and implementation from all drivers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
These have been replaced by the appropriate call to
gpio_pin_interrupt_configure(). While the disable function could be
implemented using the new functionality, the enable function cannot
because the interrupt mode is not available. Consequently we cannot
replace these with equivalent functionality using the legacy API.
Clean up the internal implementation by removing the inaccessible
port-based enable/disable feature, leaving the pin-based capability in
place.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace the common data structure with the common config structure as
a prefix of the driver-specific config structure and use the
devicetree GPIO pin counts to initialize it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update driver code and board files to use new GPIO configuration flags
such as GPIO_ACTIVE_LOW. Also add implementation of new port_* driver
API as well as gpio_pin_interrupt_configure function.
We treat GPIO_INT_MODE_LEVEL as not supported as the hardware doesn't
seem to handle level interrupts as one would expect. Looking into this
further to determine if its a HW bug or some misconfiguration in the
software.
We don't support dynamic setting of PULL_UP/PULL_DOWN config as this is
handled by pinctrl for the current boards we support the CMSDK AHB
driver on.
Tested on musca-a board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The code had GPIO_INT_DOUBLE_EDGE siliently ignored, instead lets run
-ENOTSUP so caller knows its not going to work.
Fixes: #12764
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
It needs to verify if the callback was not already installed, and if so:
if is was in controller's list.
It should return an error in case the node is not found though it was
requested to be removed.
If already inserted, it will be silently removed but added again, to
avoid circular list as stated in the bug.
Fixes#11394
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
GPIO_PIN_ENABLE, GPIO_PIN_DISABLE configuration constants overlap
functionality provided by pinmux driver. They usage makes the API
inconsistent. They are almost uniformly ignored by the existing device
drivers. Only few of them take these constants into account.
This commit deprecates usage of the two configuration constants.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The GPIO_INT_LEVEL and GPIO_INT_ACTIVE_LOW values are zero so the
statements are never executed then is better use the bit complement
masks
This issue was reported by Coverity
Coverity-CID: 157586
Change-Id: Ic8b20660a991dd3d0c71248f84c917e5ce5c3c7c
Signed-off-by: Sergio Rodriguez <sergio.sf.rodriguez@intel.com>
This patch enables the clock control interface into the ARM LTD
Beetle GPIO driver.
Jira: ZEP-1300
Change-Id: I576767b68a8e4aa965d34716528df3bb4e837d73
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
The driver is currently used only by the ARM Beetle platform.
Jira: ZEP-1245
Change-Id: I6611edd7486a3c6d82d66a9a96c5d4860dad1539
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>