Update intc drivers to use DT_HAS_<compat>_ENABLED Kconfig symbol
to expose the driver and enable it by default based on devicetree.
We remove 'depend on' Kconfig for symbols that would be implied by
the devicetree node existing.
Signed-off-by: Kumar Gala <galak@kernel.org>
The cavs_ictl interrupt controller is an interrupt aggregator
supporting multi-level interrupts. Therefore, it needs to be
initialized earlier than any downstream interrupt controllers
and devices.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
If it is such a thing (a CAVT intc), it will not be targeting Intel
s1000 SoC only. UP squarde ADSP use the same intc. So renaming it to
CAVS. Though CAVS name might be wrong (CAVS being an overall
architecture name, and not an IP block specification).
Reducing the amount of lines by using if/endif as well.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Some extensions to the multi-level interrupt controller are required
to support SoCs with more than four level 2 interrupt "aggregators".
Extend existing support to allow at most 8 level 2 or level 3
aggregators. Use Kconfig macro templates to cut down on boilerplate.
Try to clarify some aspects of the Kconfig help while we're at it, and
change the type of options which count things or are table offsets
from "hex" to "int", so that the generated .config is easier to read.
Finally, make some improvements to gen_isr_tables.py while we are
here. In particular, move some assignments around to cut down on
duplicated work, don't check for symbols we know must exist, and
improve the debug logging output's readability.
Signed-off-by: Marti Bolivar <marti@foundries.io>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
IRQ priorities for CAVS and DW were previously defined in Kconfig.
They are now defined via DTS and removed from Kconfig.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
CAVS_ICTL_0_IRQ_PRI to CAVS_ICTL_3_IRQ_PRI and DW_ICTL_IRQ_PRI
are now defined in Kconfig. This addresses the issue #7811.
This was not throwing up any compilation error earlier as the IRQ
priorities are all hardwired in Xtensa and hence are unconfigurable.
They are dummy for Xtensa arch but may be applicable if used in some
other arch.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
CAVS interrupt logic is an intel IP that combines several sources of
interrupt into one line that is then routed to the parent controller.
CAVS stands for "connected Audio, Voice and Speech". This IP supports
4 lines which can have a max of 32 interrupts each.
Change-Id: Ia6be51428bedf1011d148ae1fc5d4c34252c05da
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Kumar Gala
Kumar Gala
Daniel Leung
Tomasz Bursztyka
Ulf Magnusson
Marti Bolivar
Rajavardhan Gundi