boards: rename vendor seeed to seeed_studio

rename seeed folder to seeed_studio

Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>

CODEOWNERS

@@ -428,7 +428,7 @@
 /dts/arm64/nxp/                           @JiafeiPan
 /dts/arm64/renesas/                       @lorc @xakep-amatop
 /dts/arm/quicklogic/                      @fkokosinski @kgugala
-/dts/arm/seeed/                           @str4t0m
+/dts/arm/seeed_studio/                    @str4t0m
 /dts/arm/st/                              @erwango
 /dts/arm/st/h7/*stm32h735*                @benediktibk
 /dts/arm/st/l4/*stm32l451*                @benediktibk

boards/seeed_studio/96b_carbon/96b_carbon.yaml

@@ -15,4 +15,4 @@ supported:
   - usb_device
 ram: 96
 flash: 512
-vendor: seeed
+vendor: seeed studio

boards/seeed_studio/96b_carbon/board.yml

@@ -1,5 +1,5 @@
 board:
   name: 96b_carbon
-  vendor: seeed
+  vendor: seeed studio
   socs:
     - name: stm32f401xe

boards/seeed_studio/96b_carbon/doc/index.rst

@@ -101,7 +101,7 @@ features:
 More details about the board can be found at `96Boards website`_.
 
 The default configuration can be found in
-:zephyr_file:`boards/seeed/96b_carbon/96b_carbon_defconfig`
+:zephyr_file:`boards/seeed_studio/96b_carbon/96b_carbon_defconfig`
 
 Connections and IOs
 ===================

boards/seeed_studio/lora_e5_dev_board/doc/lora_e5_dev_board.rst

@@ -112,8 +112,8 @@ features:
 Other hardware features are not yet supported on this Zephyr port.
 
 The default configuration can be found in:
-- :zephyr_file:`boards/seeed/lora_e5_dev_board/lora_e5_dev_board_defconfig`
-- :zephyr_file:`boards/seeed/lora_e5_dev_board/lora_e5_dev_board.dts`
+- :zephyr_file:`boards/seeed_studio/lora_e5_dev_board/lora_e5_dev_board_defconfig`
+- :zephyr_file:`boards/seeed_studio/lora_e5_dev_board/lora_e5_dev_board.dts`
 
 
 Connections and IOs
@@ -214,7 +214,7 @@ set the RDP option byte to ``AA``,
 or use the STM32_Programmer_CLI passing the ``--readunprotect`` command
 to perform this read protection regression.
 The RDP level 1 to RDP level 0 regression will erase the factory programmed AT
-firmware, from which seeed has neither released the source code nor a binary.
+firmware, from which seeed studio has neither released the source code nor a binary.
 Also, note that on the module the ``BOOT0`` pin of the SOC is not accessible,
 so the system bootloader will only be executed if configured in the option bytes.
 

boards/seeed_studio/lora_e5_dev_board/lora_e5_dev_board.dts

@@ -5,7 +5,7 @@
  */
 
 /dts-v1/;
-#include <seeed/lora-e5.dtsi>
+#include <seeed_studio/lora-e5.dtsi>
 #include <zephyr/dt-bindings/input/input-event-codes.h>
 
 / {

boards/seeed_studio/lora_e5_dev_board/lora_e5_dev_board.yaml

@@ -17,4 +17,4 @@ supported:
   - uart
   - watchdog
   - lora
-vendor: seeed
+vendor: seeed studio

boards/seeed_studio/lora_e5_mini/doc/index.rst

@@ -102,8 +102,8 @@ Other hardware features are not yet supported on this Zephyr port.
 
 The default configuration can be found in:
 
-- :zephyr_file:`boards/seeed/lora_e5_mini/lora_e5_mini_defconfig`
-- :zephyr_file:`boards/seeed/lora_e5_mini/lora_e5_mini.dts`
+- :zephyr_file:`boards/seeed_studio/lora_e5_mini/lora_e5_mini_defconfig`
+- :zephyr_file:`boards/seeed_studio/lora_e5_mini/lora_e5_mini.dts`
 
 
 Connections and IOs
@@ -151,7 +151,7 @@ set the RDP option byte to ``AA``,
 or use the STM32_Programmer_CLI passing the ``--readunprotect`` command
 to perform this read protection regression.
 The RDP level 1 to RDP level 0 regression will erase the factory programmed AT
-firmware, from which seeed has neither released the source code nor a binary.
+firmware, from which seeed studio has neither released the source code nor a binary.
 Also, note that on the module the ``BOOT0`` pin of the SOC is not accessible,
 so the system bootloader will only be executed if configured in the option bytes.
 

boards/seeed_studio/lora_e5_mini/lora_e5_mini.dts

@@ -5,7 +5,7 @@
  */
 
 /dts-v1/;
-#include <seeed/lora-e5.dtsi>
+#include <seeed_studio/lora-e5.dtsi>
 #include <zephyr/dt-bindings/input/input-event-codes.h>
 
 / {

boards/seeed_studio/lora_e5_mini/lora_e5_mini.yaml

@@ -16,4 +16,4 @@ supported:
   - uart
   - watchdog
   - lora
-vendor: seeed
+vendor: seeed studio