Bluetooth: Controller: Align DDPI usage with nRF54L power domains

Align DDPI usage with nRF54L series power domains and
available DDPI configurations.

Use indices below 4 when needing to bridge with GPIO,
use indices below 8 when needing to bridge with MCU domain
like CCM and AAR; and use indices above 7 to bridge with
Peripheral domain.

Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>

subsys/bluetooth/controller/ll_sw/nordic/hal/nrf5/radio/radio_nrf5_dppi_resources.h

@@ -8,35 +8,35 @@
  * Enable Radio on Event Timer tick:
  * wire the EVENT_TIMER EVENTS_COMPARE[0] event to RADIO TASKS_TXEN/RXEN task.
  */
-#define HAL_RADIO_ENABLE_TX_ON_TICK_PPI 6
-#define HAL_RADIO_ENABLE_RX_ON_TICK_PPI 6
+#define HAL_RADIO_ENABLE_TX_ON_TICK_PPI 9
+#define HAL_RADIO_ENABLE_RX_ON_TICK_PPI 9
 
 /*******************************************************************************
  * Capture event timer on Address reception:
  * wire the RADIO EVENTS_ADDRESS event to the
  * EVENT_TIMER TASKS_CAPTURE[<address timer>] task.
  */
-#define HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI 9
+#define HAL_RADIO_RECV_TIMEOUT_CANCEL_PPI 11
 
 /*******************************************************************************
  * Disable Radio on HCTO:
  * wire the EVENT_TIMER EVENTS_COMPARE[<HCTO timer>] event
  * to the RADIO TASKS_DISABLE task.
  */
-#define HAL_RADIO_DISABLE_ON_HCTO_PPI 10
+#define HAL_RADIO_DISABLE_ON_HCTO_PPI 12
 
 /*******************************************************************************
  * Capture event timer on Radio end:
  * wire the RADIO EVENTS_END event to the
  * EVENT_TIMER TASKS_CAPTURE[<radio end timer>] task.
  */
-#define HAL_RADIO_END_TIME_CAPTURE_PPI 11
+#define HAL_RADIO_END_TIME_CAPTURE_PPI 13
 
 /*******************************************************************************
  * Start event timer on RTC tick:
  * wire the RTC0 EVENTS_COMPARE[2] event to EVENT_TIMER  TASKS_START task.
  */
-#define HAL_EVENT_TIMER_START_PPI 7
+#define HAL_EVENT_TIMER_START_PPI 8
 #define HAL_PPIB_SEND_EVENT_TIMER_START_PPI \
 	_CONCAT(NRF_PPIB_TASK_SEND_, HAL_EVENT_TIMER_START_PPI)
 #define HAL_PPIB_RECEIVE_EVENT_TIMER_START_PPI \
@@ -47,7 +47,7 @@
  * wire the RADIO EVENTS_READY event to the
  * EVENT_TIMER TASKS_CAPTURE[<radio ready timer>] task.
  */
-#define HAL_RADIO_READY_TIME_CAPTURE_PPI 8
+#define HAL_RADIO_READY_TIME_CAPTURE_PPI 10
 
 /*******************************************************************************
  * Trigger encryption task upon address reception:
@@ -62,27 +62,27 @@
  * Trigger automatic address resolution on Bit counter match:
  * wire the RADIO EVENTS_BCMATCH event to the AAR TASKS_START task.
  */
-#define HAL_TRIGGER_AAR_PPI 12
+#define HAL_TRIGGER_AAR_PPI 6
 
 #if defined(CONFIG_BT_CTLR_PHY_CODED) && \
 	defined(CONFIG_HAS_HW_NRF_RADIO_BLE_CODED)
 /*******************************************************************************
  * Trigger Radio Rate override upon Rateboost event.
  */
-#define HAL_TRIGGER_RATEOVERRIDE_PPI 13
+#define HAL_TRIGGER_RATEOVERRIDE_PPI 3
 #endif /* CONFIG_BT_CTLR_PHY_CODED && CONFIG_HAS_HW_NRF_RADIO_BLE_CODED */
 
 #if defined(HAL_RADIO_GPIO_HAVE_PA_PIN) || defined(HAL_RADIO_GPIO_HAVE_LNA_PIN)
 /******************************************************************************/
-#define HAL_ENABLE_PALNA_PPI 5
+#define HAL_ENABLE_PALNA_PPI 2
 
 #if defined(HAL_RADIO_FEM_IS_NRF21540)
-#define HAL_DISABLE_PALNA_PPI 4
+#define HAL_DISABLE_PALNA_PPI 0
 #else
 #define HAL_DISABLE_PALNA_PPI HAL_ENABLE_PALNA_PPI
 #endif
 
-#define HAL_ENABLE_FEM_PPI 3
+#define HAL_ENABLE_FEM_PPI 1
 #define HAL_DISABLE_FEM_PPI HAL_DISABLE_PALNA_PPI
 
 #endif /* HAL_RADIO_GPIO_HAVE_PA_PIN || HAL_RADIO_GPIO_HAVE_LNA_PIN */
@@ -162,11 +162,11 @@
  * when direction finding RX and PHY is set to PHY1M. Due to that it can be shared with Radio Rate
  * override.
  */
-#define HAL_TRIGGER_CRYPT_DELAY_PPI 13
+#define HAL_TRIGGER_CRYPT_DELAY_PPI 3
 #endif /* CONFIG_BT_CTLR_DF_CONN_CTE_RX */
 
 /* The 2 adjacent PPI groups used for implementing SW_SWITCH_TIMER-based
  * auto-switch for TIFS. 'index' must be 0 or 1.
  */
-#define SW_SWITCH_TIMER_TASK_GROUP_BASE 0
+#define SW_SWITCH_TIMER_TASK_GROUP_BASE 4
 #endif /* !CONFIG_BT_CTLR_TIFS_HW */